22-06-2006, 08:06
hallo Ebi,
Milliput ist eine zweikomponenten Epoxy Spachtelmasse. Du nimmst von beiden Komponenten in etwa die gleiche Masse (geht nicht so genau), dann knetest du das Zeug, um es zu vermischen. Danach ist Milliput gebrauchsfertig. Bei der Verarbeitung kann man die Spachtel mit Wasser befeuchten und die gespachtelte Stelle glätten. Milliput eignet hervorragend um die von uns so gehassten Bläschen im Resin aufzufüllen.
Hier noch ein Ausschnitt aus der Milliput homepage:
Milliput is the trade name for our epoxy putty. We produce four grades: Standard Yellow/Grey, Silver Grey, Superfine White and Terracotta. Each grade is presented in similar packs containing 2 x 56·7gm. sticks and the general instructions for preparation and usage are the same.
The two sticks have a long shelf life but once mixed the resultant putty is at first soft and highly adhesive and then gradually hardens. Speed of hardening is dependant on temperature and at normal temperatures (20-25ºC) Milliput becomes rock hard in three to four hours. By the application of heat the setting time can be reduced to a few minutes.
After setting hard Milliput continues to cure and is fully cured after an elapse of time equal to the setting time
at the same temperature. Once fully cured Milliput can be machined, drilled, tapped, turned, filed, sawn, sandpapered and painted. Milliput can be sandpapered and painted immediately it has set. (it is advisable to wear eye protection during this process).
Milliput is an excellent adhesive and will bond any of the following to itself or to any of the others - wood, brick, cement, metals, concrete, plastics, glass etc, but note that Milliput is not intended as a thin layer adhesive and should not be used where a paste, mucilage or thin glue is indicated. Milliput will set under water and is heat resistant up to 130°C.
Hoffe alles erklärt zu haben
Grüsse
leo
Milliput ist eine zweikomponenten Epoxy Spachtelmasse. Du nimmst von beiden Komponenten in etwa die gleiche Masse (geht nicht so genau), dann knetest du das Zeug, um es zu vermischen. Danach ist Milliput gebrauchsfertig. Bei der Verarbeitung kann man die Spachtel mit Wasser befeuchten und die gespachtelte Stelle glätten. Milliput eignet hervorragend um die von uns so gehassten Bläschen im Resin aufzufüllen.
Hier noch ein Ausschnitt aus der Milliput homepage:
Milliput is the trade name for our epoxy putty. We produce four grades: Standard Yellow/Grey, Silver Grey, Superfine White and Terracotta. Each grade is presented in similar packs containing 2 x 56·7gm. sticks and the general instructions for preparation and usage are the same.
The two sticks have a long shelf life but once mixed the resultant putty is at first soft and highly adhesive and then gradually hardens. Speed of hardening is dependant on temperature and at normal temperatures (20-25ºC) Milliput becomes rock hard in three to four hours. By the application of heat the setting time can be reduced to a few minutes.
After setting hard Milliput continues to cure and is fully cured after an elapse of time equal to the setting time
at the same temperature. Once fully cured Milliput can be machined, drilled, tapped, turned, filed, sawn, sandpapered and painted. Milliput can be sandpapered and painted immediately it has set. (it is advisable to wear eye protection during this process).
Milliput is an excellent adhesive and will bond any of the following to itself or to any of the others - wood, brick, cement, metals, concrete, plastics, glass etc, but note that Milliput is not intended as a thin layer adhesive and should not be used where a paste, mucilage or thin glue is indicated. Milliput will set under water and is heat resistant up to 130°C.
Hoffe alles erklärt zu haben
Grüsse
leo